A div. of

Clean Seal, Inc.

Spring and Stamping Division

(574) 299-1888

Toll-Free: 1(800) 366-3682

Clean Seal Springs Logo

 

Glossary of Terms

 

Active coils

Those coils which are free to deflect under load. Angular relationship of ends relative position of hooks or loops of an extension spring (-Lends of a torsion spring) to each other.

 

Baking

Heating of electroplated springs to relieve hydrogen embitterment.

 

Block

Length of a compression spring when deflected under sufficient load to bring all adjacent coils into contact - no additional deflection is possible.

 

Buckling

Bowing or lateral displacement of a compression spring. This effect is related to slenderness ratio L/D.

 

Closed and ground ends

Same as Closed Ends, except the first and last coils are ground to provide a flat bearing surface.

 

Closed length

Length of a compression spring when deflected under sufficient load to bring all adjacent coils into contact - no additional deflection is possible.

 

Close wound

Adjacent coils are touching.

 

Coils per inch

Distance from center to center of wire in adjacent coils in an open wound spring.

 

Deflection

Motion imparted to a spring by application or removal of an external load. Elastic Limit Maximum stress to which a material may be subjected without permanent set. Endurance Limit Maximum stress, at a given stress ratio, at which material will operate in a given environment for a stated number of cycles without failure.

 

Fixture tempering

Restraining parts during tempering to improve dimensional control.

 

Free angle

Angular relationship between arms of a helical torsion spring which is not under load.

 

Free length

Overall length of a spring which is not under load.

 

Gradient

Spring gradient, or change in load per unit of deflection.

 

Heat setting

A process to pre-relax a spring in order to improve stress relaxation resistance in service.

 

Helical springs

Springs made of bar stock or wire coiled into a helical form. This category includes compression, extension and torsion springs.

 

Hooks

Open loops or ends of extension springs.

 

Hysteresis

Mechanical energy loss occurring during loading and unloading of a spring within the elastic range. It is illustrated by the area between load deflection curves.

 

Initial tension

A force that tends to keep coils of a close wound extension spring closed and which must be overcome before the coils start to open.

 

Loops

Formed ends with minimal gaps at the ends of extension springs.

 

Mean diameter

The average diameter of the mass of spring material, equal to one half the sum of the outside and inside diameters. In a helical spring, this is the equivalent to the outside diameter minus one wire diameter.

 

Modulus in tension or bending

(Young's Modulus E) Coefficient of stiffness used for torsion or flat springs. Moment A product of the distance from the spring axis to the point of load application, and the force component normal to the distance line.

 

Modulus in shear or torsion

(Modulus of Rigidity G) Coefficient of stiffness used for compression and extension springs.

 

Natural frequency

Lowest inherent rate of free vibration of a spring vibrating between its own ends.

 

Patenting

The process of heating carbon steel above its critical temperature and cooling at a controlled rate to achieve a fine paralytic microstructure.

 

Pitch

Distance from center to center of wire in adjacent coils in an open wound spring.

 

Plain ends

End coils of a helical spring having a constant pitch and ends not squared.

 

Plain ends, ground

Same as Plain Ends, except wire ends are ground square with the axis.

 

Rate

Spring gradient, or change in load per unit of deflection.

 

Rear-end locker springs

Rear-end locker springs maintain a critical constant force on the ratcheting mechanism to ensure a smooth and consistent transfer of power to the rear drive line.

 

Residual stress

Stress mechanically induced by such means as set removal, shot peening, cold working, or forming. It may be beneficial or not, depending on the spring application.

 

Set

Permanent change of length, height or position after a spring is stressed beyond material's elastic limit.

 

Set point

Stress at which some arbitrarily chosen amount of set (usually 2%) occurs. Set percentage is the set divided by the deflection which produced it.

 

Set removal

An operation which causes a permanent loss of length or height due to spring deflection.

 

Shot peening

Blasting the surfaces of spring material with steel or glass pellets to induce compressive stresses that improve fatigue life.

 

Slenderness ratio

Ratio of spring length to mean diameter L/D in helical springs.

 

Solid height

Length of a compression spring when deflected under sufficient load to bring all adjacent coils into contact - no additional deflection is possible.

 

Spiral springs

Springs formed from flat strip or wire wound in the form of a spiral, loaded by torque about an axis normal to the plane of the spiral.

 

Spring index

Ratio of mean diameter to wire diameter.

 

Squared and ground ends

See Closed and Ground Ends.

 

Squared ends

See Closed and Ground Ends.

 

Stress range

Difference in operating stresses at minimum and maximum loads.

 

Stress ratio

Minimum stress divided by maximum stress.

 

Stress relief

A low temperature heat treatment given springs to relieve residual stresses produced by prior cold forming.

 

Torque

A product of the distance from the spring axis to the point of load application, and the force component normal to the distance line.

 

Total number of coils

The sum of the number of active and inactive coils in a spring body.

 

 

 

 

©2016 Clean Seal and its licensors.  All rights reserved.